SCITOO Boat Trailer Hub with online shop Galvanized Lug Bol on Idler 4 /brunetness926137.html,Idler,Trailer,Sports Outdoors , Sports Fitness , Boating Sailing,SCITOO,Hub,Bol,$41,4,Galvanized,therunclub.in,with,Boat,4,Hub,Lug,on $41 SCITOO Boat Trailer Hub with Galvanized Idler Hub 4 Lug on 4 Bol Sports Outdoors Sports Fitness Boating Sailing $41 SCITOO Boat Trailer Hub with Galvanized Idler Hub 4 Lug on 4 Bol Sports Outdoors Sports Fitness Boating Sailing /brunetness926137.html,Idler,Trailer,Sports Outdoors , Sports Fitness , Boating Sailing,SCITOO,Hub,Bol,$41,4,Galvanized,therunclub.in,with,Boat,4,Hub,Lug,on SCITOO Boat Trailer Hub with online shop Galvanized Lug Bol on Idler 4

SCITOO Boat Trailer Hub with online shop Galvanized Lug discount Bol on Idler 4

SCITOO Boat Trailer Hub with Galvanized Idler Hub 4 Lug on 4 Bol

$41

SCITOO Boat Trailer Hub with Galvanized Idler Hub 4 Lug on 4 Bol

|||

Product description

Package Quantity:
1x Hot Dip Galvanized Hub
1x Inner Bearing
1x Outer Bearing
1x Dust Cap
4x cone wheel Lug Nuts
2x Grease seals
1x Cotter key

Parameter:
Outer bearing 44649-- 1 1/16" inner diameter
Inner bearing 44649-- 1 1/16" inner diameter
Seal inside diameters are 1.25" and 1.5"Seal outside diameters are 1.983"
4 on 4" Bolt Pattern
Fit for 2000lbs

Installation Instructions:
Step 1: Remove the existing dust cap, cotter pin, castle nut, washer and hub. Remove any remaining grease from spindle. Inspect for spindle for wear or damage.
Step 2: Slide new hub onto spindle. Using a torque wrench, tighten the new castle nut to 30-40 foot-lbs. Turn hub to ensure proper bearing seating, Loosen the castle nut until loose enough to turn the castle nut with you fingers. Re-tighten the castle nut finger tight.
Step 3: Install cotter pin through the hole in the spindle. If the hole is covered by the castle nut, loosen the castle nut to the nearest hole so that the cotter pin can be installed. The hub should rotate freely when spun by hand, and there should be no movement when the hub is pulled back and forth. Bend the legs of the cotter pin to ensure the cotter pin and castle nut will not loosen.
Step 4: Install the dust cap with the dust cap installation tool. Use a mallet or hammer, only strike the dust cap tool and not the dust cap(Helpful hint):Place piece of wood over the dust cap tool.
Step 5: Start all nuts by hand to prevent cross threading. Tighten the lug nuts in stages. Following the sequence and torque stages per your specific hub and wheel size.Wood block(not supplied)

SCITOO Boat Trailer Hub with Galvanized Idler Hub 4 Lug on 4 Bol

American Shifter 464592 Shifter Kit (2004R 12 Trim Kit BLK Dual
Why Choose MedStar Health?
Convenient Access
Continuous Learning
Committed to Our Communities
We strive to make world-class health care accessible through easy, convenient access.
As partners with Georgetown University for nearly 20 years, we are training the next generation of physicians.
We are committed to the health and wellness of the communities we serve.
Convenient Access
We strive to make world-class health care accessible through easy, convenient access.
Continuous Learning
As partners with Georgetown University for nearly 20 years, we are training the next generation of physicians.
Committed to Our Communities
We are committed to the health and wellness of the communities we serve.
  • Karbay Carburetor Repair Kit For SS Master Rebuild Kit Carb Reb
    Latest News
    Nationally Renowned Transplant Surgeon Matthew Cooper, MD to Lead United Network for Organ Sharing Board of Directors Read More